diff --git a/board/gumstix/duovero/duovero.c b/board/gumstix/duovero/duovero.c
new file mode 100644
index 0000000..81d6c82
--- /dev/null
+++ b/board/gumstix/duovero/duovero.c
@@ -0,0 +1,264 @@
+/*
+ * (C) Copyright 2013
+ * Gumstix Inc. <www.gumstix.com>
+ * Maintainer: Ash Charles  <ash@gumstix.com>
+ *
+ * SPDX-License-Identifier:     GPL-2.0+
+ */
+#include <common.h>
+#include <netdev.h>
+#include <asm/arch/sys_proto.h>
+#include <asm/arch/mmc_host_def.h>
+#include <twl6030.h>
+#include <asm/emif.h>
+#include <asm/arch/clock.h>
+#include <asm/arch/gpio.h>
+#include <asm/gpio.h>
+
+#include "duovero_mux_data.h"
+
+#define WIFI_EN	43
+
+#if defined(CONFIG_CMD_NET)
+#define SMSC_NRESET	45
+static void setup_net_chip(void);
+#endif
+
+#ifdef CONFIG_USB_EHCI
+#include <usb.h>
+#include <asm/arch/ehci.h>
+#include <asm/ehci-omap.h>
+#endif
+
+DECLARE_GLOBAL_DATA_PTR;
+
+const struct omap_sysinfo sysinfo = {
+	"Board: duovero\n"
+};
+
+struct omap4_scrm_regs *const scrm = (struct omap4_scrm_regs *)0x4a30a000;
+
+/**
+ * @brief board_init
+ *
+ * @return 0
+ */
+int board_init(void)
+{
+	gpmc_init();
+
+	gd->bd->bi_arch_number = MACH_TYPE_OMAP4_DUOVERO;
+	gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100;
+
+	return 0;
+}
+
+/**
+ * @brief misc_init_r - Configure board specific configurations
+ * such as power configurations, ethernet initialization as phase2 of
+ * boot sequence
+ *
+ * @return 0
+ */
+int misc_init_r(void)
+{
+	int ret = 0;
+	u8 val;
+
+	/* wifi setup: first enable 32Khz clock from 6030 pmic */
+	val = 0xe1;
+	ret = i2c_write(TWL6030_CHIP_PM, 0xbe, 1, &val, 1);
+	if (ret)
+		printf("Failed to enable 32Khz clock to wifi module\n");
+
+	/* then setup WIFI_EN as an output pin and send reset pulse */
+	if (!gpio_request(WIFI_EN, "")) {
+		gpio_direction_output(WIFI_EN, 0);
+		gpio_set_value(WIFI_EN, 1);
+		udelay(1);
+		gpio_set_value(WIFI_EN, 0);
+		udelay(1);
+		gpio_set_value(WIFI_EN, 1);
+	}
+
+#if defined(CONFIG_CMD_NET)
+	setup_net_chip();
+#endif
+	return 0;
+}
+
+void set_muxconf_regs_essential(void)
+{
+	do_set_mux((*ctrl)->control_padconf_core_base,
+		   core_padconf_array_essential,
+		   sizeof(core_padconf_array_essential) /
+		   sizeof(struct pad_conf_entry));
+
+	do_set_mux((*ctrl)->control_padconf_wkup_base,
+		   wkup_padconf_array_essential,
+		   sizeof(wkup_padconf_array_essential) /
+		   sizeof(struct pad_conf_entry));
+
+	do_set_mux((*ctrl)->control_padconf_core_base,
+		   core_padconf_array_non_essential,
+		   sizeof(core_padconf_array_non_essential) /
+		   sizeof(struct pad_conf_entry));
+
+	do_set_mux((*ctrl)->control_padconf_wkup_base,
+		   wkup_padconf_array_non_essential,
+		   sizeof(wkup_padconf_array_non_essential) /
+		   sizeof(struct pad_conf_entry));
+}
+
+#if !defined(CONFIG_SPL_BUILD) && defined(CONFIG_GENERIC_MMC)
+int board_mmc_init(bd_t *bis)
+{
+	return omap_mmc_init(0, 0, 0, -1, -1);
+}
+#endif
+
+
+#if defined(CONFIG_CMD_NET)
+
+#define GPMC_SIZE_16M	0xF
+#define GPMC_BASEADDR_MASK	0x3F
+#define GPMC_CS_ENABLE		0x1
+
+static void enable_gpmc_net_config(const u32 *gpmc_config, struct gpmc_cs *cs,
+		u32 base, u32 size)
+{
+	writel(0, &cs->config7);
+	sdelay(1000);
+	/* Delay for settling */
+	writel(gpmc_config[0], &cs->config1);
+	writel(gpmc_config[1], &cs->config2);
+	writel(gpmc_config[2], &cs->config3);
+	writel(gpmc_config[3], &cs->config4);
+	writel(gpmc_config[4], &cs->config5);
+	writel(gpmc_config[5], &cs->config6);
+
+	/*
+	 * Enable the config.  size is the CS size and goes in
+	 * bits 11:8.  We set bit 6 to enable this CS and the base
+	 * address goes into bits 5:0.
+	 */
+	writel((size << 8) | (GPMC_CS_ENABLE << 6) |
+				 ((base >> 24) & GPMC_BASEADDR_MASK),
+				 &cs->config7);
+
+	sdelay(2000);
+}
+
+/* GPMC CS configuration for an SMSC LAN9221 ethernet controller */
+#define NET_LAN9221_GPMC_CONFIG1    0x2a001203
+#define NET_LAN9221_GPMC_CONFIG2    0x000a0a02
+#define NET_LAN9221_GPMC_CONFIG3    0x00020200
+#define NET_LAN9221_GPMC_CONFIG4    0x0a030a03
+#define NET_LAN9221_GPMC_CONFIG5    0x000a0a0a
+#define NET_LAN9221_GPMC_CONFIG6    0x8a070707
+#define NET_LAN9221_GPMC_CONFIG7    0x00000f6c
+
+/* GPMC definitions for LAN9221 chips on expansion boards */
+static const u32 gpmc_lan_config[] = {
+	NET_LAN9221_GPMC_CONFIG1,
+	NET_LAN9221_GPMC_CONFIG2,
+	NET_LAN9221_GPMC_CONFIG3,
+	NET_LAN9221_GPMC_CONFIG4,
+	NET_LAN9221_GPMC_CONFIG5,
+	NET_LAN9221_GPMC_CONFIG6,
+	/*CONFIG7- computed as params */
+};
+
+/*
+ * Routine: setup_net_chip
+ * Description: Setting up the configuration GPMC registers specific to the
+ *	      Ethernet hardware.
+ */
+static void setup_net_chip(void)
+{
+	enable_gpmc_net_config(gpmc_lan_config, &gpmc_cfg->cs[5], 0x2C000000,
+			      GPMC_SIZE_16M);
+
+	/* Make GPIO SMSC_NRESET as output pin and send reset pulse */
+	if (!gpio_request(SMSC_NRESET, "")) {
+		gpio_direction_output(SMSC_NRESET, 0);
+		gpio_set_value(SMSC_NRESET, 1);
+		udelay(1);
+		gpio_set_value(SMSC_NRESET, 0);
+		udelay(1);
+		gpio_set_value(SMSC_NRESET, 1);
+	}
+}
+#endif
+
+int board_eth_init(bd_t *bis)
+{
+	int rc = 0;
+#ifdef CONFIG_SMC911X
+	rc = smc911x_initialize(0, CONFIG_SMC911X_BASE);
+#endif
+	return rc;
+}
+
+#ifdef CONFIG_USB_EHCI
+
+static struct omap_usbhs_board_data usbhs_bdata = {
+	.port_mode[0] = OMAP_EHCI_PORT_MODE_PHY,
+	.port_mode[1] = OMAP_USBHS_PORT_MODE_UNUSED,
+	.port_mode[2] = OMAP_USBHS_PORT_MODE_UNUSED,
+};
+
+int ehci_hcd_init(int index, enum usb_init_type init,
+		struct ehci_hccr **hccr, struct ehci_hcor **hcor)
+{
+	int ret;
+	unsigned int utmi_clk;
+	u32 auxclk, altclksrc;
+
+	/* Now we can enable our port clocks */
+	utmi_clk = readl((void *)CM_L3INIT_HSUSBHOST_CLKCTRL);
+	utmi_clk |= HSUSBHOST_CLKCTRL_CLKSEL_UTMI_P1_MASK;
+	setbits_le32((void *)CM_L3INIT_HSUSBHOST_CLKCTRL, utmi_clk);
+
+	auxclk = readl(&scrm->auxclk3);
+	/* Select sys_clk */
+	auxclk &= ~AUXCLK_SRCSELECT_MASK;
+	auxclk |=  AUXCLK_SRCSELECT_SYS_CLK << AUXCLK_SRCSELECT_SHIFT;
+	/* Set the divisor to 2 */
+	auxclk &= ~AUXCLK_CLKDIV_MASK;
+	auxclk |= AUXCLK_CLKDIV_2 << AUXCLK_CLKDIV_SHIFT;
+	/* Request auxilary clock #3 */
+	auxclk |= AUXCLK_ENABLE_MASK;
+	writel(auxclk, &scrm->auxclk3);
+
+	altclksrc = readl(&scrm->altclksrc);
+
+	/* Activate alternate system clock supplier */
+	altclksrc &= ~ALTCLKSRC_MODE_MASK;
+	altclksrc |= ALTCLKSRC_MODE_ACTIVE;
+
+	/* enable clocks */
+	altclksrc |= ALTCLKSRC_ENABLE_INT_MASK | ALTCLKSRC_ENABLE_EXT_MASK;
+
+	writel(altclksrc, &scrm->altclksrc);
+
+	ret = omap_ehci_hcd_init(index, &usbhs_bdata, hccr, hcor);
+	if (ret < 0)
+		return ret;
+
+	return 0;
+}
+
+int ehci_hcd_stop(int index)
+{
+	return omap_ehci_hcd_stop();
+}
+#endif
+
+/*
+ * get_board_rev() - get board revision
+ */
+u32 get_board_rev(void)
+{
+	return 0x20;
+}